The lever type matters too. Close-coupled cisterns almost always use a side lever or a push button through the lid, while older low-level suites more often run a side lever connected by an external link arm. Ordering a replacement lever without checking which type is fitted is a common cause of parts being sent back.
Fixing centres, meaning the distance between the two mounting holes in the pan, is the measurement that actually determines whether a seat will fit at all, and it varies enough between manufacturers that assuming a standard spacing is a common source of returned parts. The two most frequently seen spacings in the UK are around 140mm to 145mm and 160mm to 165mm centre to centre, and a seat bought for the wrong spacing simply will not sit over both holes.
Start with the fill valve. This is the mechanism that lets water into the cistern after a flush and shuts off once the tank reaches the correct level, usually via a float or a diaphragm. When a fill valve wears, the most common signs are a hissing or trickling noise that continues long after the cistern should have stopped filling, a water level creeping up to or past the overflow pipe, or a float arm that no longer rises high enough to trigger shut-off. Mineral deposits inside the valve seat are often the culprit, particularly in hard water areas, and once the seal degrades a full replacement is usually more reliable than trying to clean it out.
Cable-actuated systems use a flexible cable in place of the rigid spindle, which allows the button to be positioned somewhere other than directly above the flush valve, useful on concealed cisterns and certain close-coupled designs where the lid mechanism does not line up with the valve beneath. The cable itself can stretch, kink or seize inside its outer sheath over time, and a button that has become stiff, or one that no longer springs back after use, usually points to the cable rather than the flush valve itself.
See more on this at plumbers merchants.
A flush valve, by contrast, works as a straightforward seal at the base of the cistern that lifts to let water fall directly through into the pan under gravity, with no siphoning action involved, and plumb2u trade counter shuts again once the float or timer mechanism allows it to reseat. Flush valves are what almost all dual-flush cisterns use, since a siphon's all-or-nothing action makes a genuine short flush difficult to achieve, whereas a valve can simply be held open for a shorter or longer period.
Fixing centres, meaning the distance between the two mounting holes in the pan, is the measurement that actually determines whether a seat will fit at all, and it varies enough between manufacturers that assuming a standard spacing is a common source of returned parts. The two most frequently seen spacings in the UK are around 140mm to 145mm and 160mm to 165mm centre to centre, and a seat bought for the wrong spacing simply will not sit over both holes.
Start with the fill valve. This is the mechanism that lets water into the cistern after a flush and shuts off once the tank reaches the correct level, usually via a float or a diaphragm. When a fill valve wears, the most common signs are a hissing or trickling noise that continues long after the cistern should have stopped filling, a water level creeping up to or past the overflow pipe, or a float arm that no longer rises high enough to trigger shut-off. Mineral deposits inside the valve seat are often the culprit, particularly in hard water areas, and once the seal degrades a full replacement is usually more reliable than trying to clean it out.
Cable-actuated systems use a flexible cable in place of the rigid spindle, which allows the button to be positioned somewhere other than directly above the flush valve, useful on concealed cisterns and certain close-coupled designs where the lid mechanism does not line up with the valve beneath. The cable itself can stretch, kink or seize inside its outer sheath over time, and a button that has become stiff, or one that no longer springs back after use, usually points to the cable rather than the flush valve itself.
See more on this at plumbers merchants.
A flush valve, by contrast, works as a straightforward seal at the base of the cistern that lifts to let water fall directly through into the pan under gravity, with no siphoning action involved, and plumb2u trade counter shuts again once the float or timer mechanism allows it to reseat. Flush valves are what almost all dual-flush cisterns use, since a siphon's all-or-nothing action makes a genuine short flush difficult to achieve, whereas a valve can simply be held open for a shorter or longer period.
