On button-actuated cisterns with a rigid spindle, the button sits directly above a plastic or metal rod that passes through the cistern lid and connects to a lever arm on the flush valve below. Pressing the small button rotates or depresses the spindle partially, lifting the flush valve seal just enough for a short flush. Pressing the full button pushes the spindle further, lifting the valve completely so the cistern empties in one go. Wear at the point where the spindle meets the flush valve lever is the most common failure here, often showing up as a button that clicks but produces no flush, or a short flush that no longer fires at all while the full flush still works.
The second check is a knocking or banging sound, sometimes called water hammer, that happens specifically at the moment the fill valve shuts off rather than during the fill itself. This is far more often a mains pressure issue than a valve fault, caused by the sudden stop of a fast-moving column of water hitting the closed valve and sending a shock through the pipework. A fill valve replacement on its own will sometimes quieten this slightly, particularly if swapping to a bottom-entry valve which fills more gently, but it will not fully resolve a genuine water hammer problem, which usually needs an air-filled arrestor fitted at the supply if it persists.
A close-coupled cistern bolts directly onto the back of the pan with no visible pipework between the two. Because the outlet on the cistern base sits directly above the inlet on the pan, the flush valve or siphon needs a shorter outlet and often a rubber doughnut washer to seal the joint rather than a length of pipe. Fill valves on close-coupled units tend to be shorter in the body too, since there is less depth inside a compact tank.
See the details at PLUMB2U.
Identifying which mechanism is fitted before ordering a spare avoids a wasted trip, since a flush valve will not fit where a siphon body was designed to sit and vice versa. Lifting the cistern lid and looking for a vertical tube with a bell-shaped top, rather than a flat valve seated directly over the outlet, is usually enough to tell the two apart on site. Plumb2U stocks siphon replacement units and modern flush valves side by side, at trade prices, for plumbers working across the full range of cistern ages found on a typical UK round. With next-day despatch on the common lines, Plumb2U's range covers the older gravity-fed jobs as readily as the newer dual-flush cisterns.
A dual-flush button looks simple from the top of the cistern lid, but underneath it is doing a more complicated job than a single-flush handle ever had to. Pressing one half of the button needs to trigger a short flush, while the other half needs to lift the flush valve fully for a complete cycle, and the mechanism that makes this happen is usually either a rigid spindle or a flexible cable running down to the flush valve itself.
The second check is a knocking or banging sound, sometimes called water hammer, that happens specifically at the moment the fill valve shuts off rather than during the fill itself. This is far more often a mains pressure issue than a valve fault, caused by the sudden stop of a fast-moving column of water hitting the closed valve and sending a shock through the pipework. A fill valve replacement on its own will sometimes quieten this slightly, particularly if swapping to a bottom-entry valve which fills more gently, but it will not fully resolve a genuine water hammer problem, which usually needs an air-filled arrestor fitted at the supply if it persists.
A close-coupled cistern bolts directly onto the back of the pan with no visible pipework between the two. Because the outlet on the cistern base sits directly above the inlet on the pan, the flush valve or siphon needs a shorter outlet and often a rubber doughnut washer to seal the joint rather than a length of pipe. Fill valves on close-coupled units tend to be shorter in the body too, since there is less depth inside a compact tank.
See the details at PLUMB2U.
Identifying which mechanism is fitted before ordering a spare avoids a wasted trip, since a flush valve will not fit where a siphon body was designed to sit and vice versa. Lifting the cistern lid and looking for a vertical tube with a bell-shaped top, rather than a flat valve seated directly over the outlet, is usually enough to tell the two apart on site. Plumb2U stocks siphon replacement units and modern flush valves side by side, at trade prices, for plumbers working across the full range of cistern ages found on a typical UK round. With next-day despatch on the common lines, Plumb2U's range covers the older gravity-fed jobs as readily as the newer dual-flush cisterns.
A dual-flush button looks simple from the top of the cistern lid, but underneath it is doing a more complicated job than a single-flush handle ever had to. Pressing one half of the button needs to trigger a short flush, while the other half needs to lift the flush valve fully for a complete cycle, and the mechanism that makes this happen is usually either a rigid spindle or a flexible cable running down to the flush valve itself.
